Produkty dla mini automaty (11)

Reparatur, Austausch & Ersatz für ABB Robotersysteme und ABB IRC5 & S4 Pendants Seit Anfang 2018 bieten wir Ihnen generalüberholende Reparaturen sowie Austauschteile und Ersatzteile für Roboter-Bedienhandgeräte der Produktreihen IRC5, IRC5P, S4, S4+, S4C+, S4P sowie S4P+ des Herstellers ABB an. Ab sofort bieten wir Ihnen unsere umfassenden Serviceleistungen auch für alle ABB-Baugruppen (Antriebe, IPCs, Netzteile, Motoren, Kabel uvm.) aus dem Bereich der Robotersteuerungselektronik folgender Baureihen an: • S2 / S3 • S4 / S4C / S4C+ • S4P / S4P+ • IRC5 Neben der Verwendung von vom Hersteller oder Gesetzesgeber zugelassenen Bauteile testen wir die generalüberholten ABB Bedienhandgeräte und ABB Robotersysteme mit originalen IRB ABB-Robotern unter Bedingungen, die Ihrem realen Arbeitsumfeld entsprechen. Damit können wir Ihnen auch hier 24 Monate Gewährleistung* auf die komplette ABB Baugruppe geben.

The Mini Shaft Loader allows you to load short shafts. The loading is done automatically. Do you have remnants of long bar feeder and would you like to process them? Or do you want to load very short shafts automatically? The MSL is the ideal complement for the Multi-3000 to load short shafts. It has a multi-profile loading prism. So you can load round and hexagonal material and all this without changing channels. Special profiles are possible on request. Impact-free recharging thanks to the exclusive recharging cycle. The recharging cycle is based on the patented recharging mechanism of the Multi 3000. After fast and precise bar removal, the material is gently placed on the loading prism. The Mini Shaft Loader is connected to the bar feeder. This takes over the power supply and control of the loading system. The material is fed via the slide of the loading magazine. Round profile:Ø 5-65 mm Hexagonal material:Ø 5-56 mm Square material:Option Wave length:40-250 mm* Bar feed:servo motor of the existing bar feeder * max. standard length 140mm. :Other lengths available as an option on request.

Pneumatic timers are used for the precise time control of pneumatic signals in pneumatic circuits or systems. The pressure-independent function of time delay starts when pressure is applied to the control port. After the pre-selected time is elapsed, an internal 3/2 way valve is switched. The pneumatic timer is reset to the initial condition if the control port is vented for at least 300 ms. The adjustable time delay depends on the chosen version and amounts between 0.5 and 180 s. Due to its design the control pressure level must not be below working pressure level. As a result of the fire-risk evaluation according to EN 13463-1, the pneumatic timers are not subject to ATEX regulations. This means they may also be used in explosion hazardous areas as defined in IIG/ IID. Time intervall:0.5 - 60 s  Function:3/2-way NC  Pressure range:1.5 - 8 bar Type of pneumatic connection:1/8 NPT  Product type:Timer  Mounting:Subplate  Medium:Compressed air, non lubricated  Ambient temperature:-10 ... +60 °C

With digital Master-Slave function, overload protection and interference filter. Protection for your appliance from malfunctions in the mains, such as surges, indirect lightning strikes or circuit noises, with a maximum sum of leakage current of up to 30.000 A. Top quality protection against HF interference by means of an integrated filter. With the switching ON/OFF of the device, which is plugged into the red master socket, all further appliances in the slave socket can also be automatically switched ON/OFF. For example, you can use a computer as a master device, which can embrace slave appliances in the automatic control such as, e.g. monitor, sound-system, printer, scanner etc. Meets the high standards for the environmental safety symbol "The Blue Angel" - minimizes standby losses - low energy consumption - avoids materials that pollute the environment. Digital: Saves the correct setting for your master unit at the push of a button. Modern: Switches your slave unit safe and...

Einhell mini remote control HS 434/6, 434 MHz 6-channels Coding: 16.7 million possibilities, for garage door operators BGT 63, BM 60, TA 160, TA-G 63, TA-G 83, TA-G 103, GTA 160, GTA 163, side hinged gate operator AFA 2601,EFA 1200, FA-G 2601, FAG 1601 Dimensions: 38 x 50 x 15 mm, battery: 23 A, 12 V Programming the transmitters: Hold the learning key located in the operator down for 4 seconds until the red control LED goes on. Then release the button and press the chosen control button on the manual transmitter. The red LED now off. The control code has now been stored. Note: You can store a max. 3 manual transmitters in the operator. If a fourth transmitter is stored, the code set for the first transmitter is lost. The control code is not lost in case of power failure. With malfunction pull the mains plug and repeat operation. If you want to use more than 3 transmitters, an additional receiver must be installed in the receiver /operator, than you may order transmitter...

Der Hersteller ICP DAS bietet mit dem tM-7565 einen kleinen Konverter an, der es erlaubt, CAN-Bus kompatible Geräte unkompliziert über USB anzubinden. Über einen speziellen Treiber wird in der Windows Systemsteuerung eine „virtuelle CAN-Schnittstelle“ erzeugt, über die das CAN-Gerät einfach angesprochen und gemanagt werden kann. Hersteller:ICP DAS Montage:DIN-Rail CAN Version:ISO-11898-2, CAN 2.0A, CAN 2.0B

Inserted into the mini display port to block an unused mini display port and prevent access by unauthorised persons.

The compact, highresolution MiniCODERs from Lenord+Bauer have proven their value for speed and position acquisition in highly dynamic applications. They use their full potential when installation situations with little space require a particularly compact, robust and reliable measuring system. The magnetic measuring systems consist of a ferromagnetic target wheel and a scanning unit. Without dedicated bearings, they are completely wearfree and maintenancefree. The optimised circuit and screening technique, and fully encapsulated electronics ensure reliable operation even in harsh environments. High measuring accuracy and compact design have made MiniCODERs the most frequently used speed sensors in highspeed spindles in the world. More than 500,000 pieces are installed, among other things, in machines for highspeed cutting. They are suitable for speed and position detection in all highly dynamic applications and offer now also digital motorfeedback.

RFID – Transponder mit Temperatursensor zur Überwachung von Kabel und elektrischen Anlagen.

Unlocks some of SMARTKEEPER PRO lock products : Mini USB-B, Mirco USB-B, RJ11, Mini Display, USB-C port locks.

Plugs into the USB-B port to block unused USB-B ports to prevent unauthorised access.